TopOil

Surface Preparation

Wood surface must be clean, dry and frost-free (moisture content max. 18%).

Osmo TopOil is ready to use. Do not thin. Stir well before use.

Clean old microporous stains thoroughly. Old paints and lacquers must be completely removed. As a general rule, wear a dust mask during sanding works.

Fill small cracks, larger joints or holes in wood (with Osmo Wood Filler).

Sand wood surfaces carefully. Begin with coarse sandpaper then progress to finer grades– final sanding work for furniture P150-240 (depending on wood species ). For kitchen work tops using absorbent hardwoods like Oak or Beech, final sanding grade P120. For very absorbent woods like Pine, sand to a maximum of P150.

For dark and extractive-rich woods (e.g. Iroko, Teak, Mahogany, Sapele, Wenge, Merbau, Jatoba, Cedar etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.

Before oiling the surface, remove sanding dust with a soft brush or vacuum cleaner.

The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.

Method of Application

Apply the first coat thinly along the wood grain with an Osmo Microfibre Roller, Flat Brush or Oil Finish Applicator Fleece.

Allow to dry for approx. 8-10 hours. Ventilate well while drying.

Apply the second coat with an Osmo Oil Finish Applicator Fleece or a lint-free cloth.  Avoid covering during drying and curing. After 2-3 weeks, the surface is fully cured.

For renovations, one coat applied to the clean and dry surface with an Oil Finish Applicator Fleece or lint-free cloth is usually sufficient.

Note

TopOil 3028 and TopOil 3058 Clear enhances the tone of wood (permanent wet effect). TopOil 3068 Natural is slightly white tinted and counteracts exactly this effect. If applied correctly, 3068 Natural protects wood nearly invisibly and the natural colour tone of wood is preserved. TopOil 3068 Natural is visible as a slightly white chalky surface on dark/reddish wood species. Applying excess TopOil 3068 may lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry.

Transparent TopOils (e.g. 3061 Acacia) are lightly pigmented, which give the wood an elegant look.

Applying the product too generously and insufficient ventilation lead to delays in drying time. For cabinet interiors and drawers, apply max. one coat thinly with a cloth. Allow for good ventilation while drying.

If a higher gloss level is desired, after thoroughly drying apply Osmo Liquid Wax Cleaner (also available as Spray) thinly and polish when dry.

Wood surfaces treated with TopOil are easy to clean.

Add Osmo Wash and Care concentrate to mop water and clean the surface with a damp (not wet!) cloth.

Use Osmo Liquid Wax Cleaner to remove tough stains, which cleans and regenerates the surface at the same time.

Using general or multi-purpose cleaners will increase the frequency of maintenance and recoating. Allow finish to fully cure before heavy usage.

Care

Regular Cleaning: Dust mopping. Damp mopping using Osmo Spray-Cleaner.

Occasional Maintenance: Intensive cleaning and refreshing using Osmo Liquid Wax Cleaner or Osmo Maintenance Oil.

Recoating: Simply re-apply one coat onto the clean and dry surface when signs of wear become visible.

Download the PDF product information and safety data here:

Product Information

Safety Data

RECOMMENDED

• Oak
• Pine
• Spruce
• Beech
• Ash
• Alder
• Douglas Fir
• Birch
• Larch

POSSIBLE

Maple:

apply very thinly and carry out a trial application before use.

American/European Walnut:

apply very thinly and carry out a trial application before use.

NOT RECOMMENDED

The wood species below are not recommended for Polyx-Oil Original. Please use Osmo Wood Wax Finish Extra Thin instead.

• Cedar
• Iroko
• Mahogany
• Teak
• South American Walnut
• Sapele
• Bamboo
• Acacia
• Ipe
• Merbau
• Ebony
• Wenge
• Ipe
• Sycamore
• Rosewoo

ALSO NOT RECOMMENDED

Green Oak: moisture content is often above the maximum 20% recommended.

Idigbo: contains yellow dyes which leaches when the wood becomes wet and stains when in contact within iron.

Other woods treated with a varnish, lacquer or other surface coatings must be completely sanded before use.

Top Tips:

• Shake very well before use. Failure to mix all ingredients ( and colour) could lead to an increased patchiness.
• For dark and extractive-rich woods (e.g. Iroko, Teak, Mahogany, Sapele, Wenge, Merbau, Jatoba, Cedar etc.), we recommend using Osmo Wood Wax Finish Clear Extra Thin. A trial application is recommended.
• For kitchen worktops, Osmo Wood Protector 4006 is an optional pre-treatment for absorbent wood like: Pine, Birch or Spruce. Osmo Wood Protector 4006 will help to raise the water repellant qualities of the timber prior to applying Osmo Top Oil.
• Wood pre-treated with Osmo Wood Protector 4006 may appear a little more dark and colour intensified. Always trial apply Osmo Top Oil 3068 Natural over the Wood Protector 4006 to ensure the final appearance meets with expectations.
• Osmo TopOil 3068 Natural is slightly white tinted and is optically suitable for lighter coloured wood species, eg : Oak, Beech, Birch or Pine. On dark/reddish wood species, Osmo TopOil 3068 Natural is visible as slightly white chalky surface.
• Applying excess Osmo TopOil 3068 Natural may lead to a white chalky surface. Remove visible white pigments before allowing the surface to dry.
• Avoid covering during drying and curing. After 2-3 weeks, the surface is fully cured.
• Multi-purpose cleaners such as washing up liquids and detergents are highly detrimental to the finished surface and is not recommended to be used as discolouration or staining may be possible.
• Other household cleaning products such as vanish, bleach, baking soda etc. are likely to cause severe discolouration or staining.

Microporous natural hardwax-oil wood finish which is extremely tough and hardwearing. It is water repellent and dirt resistant. The finish is resistant against wine, beer, cola, coffee, tea, fruit juices, milk and water. These types of liquid spillages will tightly bead on the surface without leaving any marks, simply clean by wiping with a cloth.